TESCO Top Drive spare parts 123285 30123286 30123287 30123288 30123289 30123562 30123563 30123564 810139 720993 5031016

Short Description:

Tesco top drive spare parts list:

5105 Valve,Ball
5127 Fitting
5128 Fitting
5140
5149 Fitting
5166
5175 Gauge
5178
5258
5317 HOUSE Hyd, 100R2-AT#12×75-fit FJICxFJIC (#5317)
5323
5397 Fitting
5401 Hose, Hyd, 100R2-AT, #6×26″, FJICxFJIC, Part # 5401, MFg. TESCO
5438 hose hyd
5439 hose hyd
5449
5456 hose hyd
5459 hose hyd
5481 Hose,Hyd,100R2-AT,#8×44″,FJICxFJIC
5490 hose hyd
5491 hose hyd
5707 Fitting
5717 seal
5763
5889 Washpipe Core,200T Swivel,RSTL,200T Swivel,HMI / Washpipe,RSTL,200T Swivel,HMI
5906 Fitting,Hyd,90°Elb,#12MJICx#16MNPT
5966 Screw
5969 Screw,Cap,Skt Hd,14″-20UNCx12″,Dr Hd
5997 Actuator,Mudsaver Valve,5187-TDA-Ser-C
6027 CYLINDER, MODIFIED, HMI LINK TILT
6030 hose hyd
6060 SWITCH,PROX,NAMUR,18AWG,P&F
6085 Screw
6115
6127
6147 Fitting,Hyd,Plug,Skt Hd,38″MNPT
6200 Swivel Link Pin Stop / Retainer,Pin,Swivel Link
6208 Flow Meter,In-Line,Bi-Directional,Petroleum Fluids,1-14″FORB,10-100 GPM,5000-psi,Stainless Steel
6285 Fitting, Hyd, Str, #4MNPT x 4 MJIC, Part # 6285, MFg. TESCO
6451 Screw
6463 Screw
6464 Screw,Cap,Skt Hd,58″-11UNCx2-12″,Dr Hd,(3 Hole)
6544 Seal,6.000″Shaftx7.508″ODx0.562″W,Type 410,Nitrile
6618 TARP,HOSE
6619
6700
6839 Bushing,2.002″ODx1.505″IDx0.990″W Tesco 6839
6925 Screw,Cap,Hex Hd,12″-13UNCx2-12″,Gr8,Pld,Dr Hd
6997 Fitting
6999 Relief valve, cartridge, RVDA1ON
7080
7316 Ring seal, rubber, N70-244,4.234″ Ø inner x 0.139″ thick O-Ring,N70-244,4.234″IDx0.139″Dia
7320 seal
7443
7452 Bearing, Support, Roller, Tapered, 14.5″ Ø Outer x 7.0″ Ø Inner x 3.25″ Thick Bearing,Thrust,Rlr,Tpr,14.5″ODx7.0″IDx3.25″Thk
7490 FILTER, DONALDSON, WIREMESH 100 FCOOLER
7602
7747 Screw,Cap,Hex Hd,12″-13UNCx4-12″,Gr8,Plt,Dr Thd
7847 Heater,XP,Tank,1.5kW,600V,1Ø,2″NPT,WThermostat
7963 clamps
10333 Bearing cap lower
10497 Connector
10523 Fitting,Hyd,Str,#16MJICx#16FNPT
10632 Washer,Flat,Type A,Narrow,38″,Hardened,Pld
10635 washer
10736
10737
10854 Fitting,Hyd,Plug,Skt Hd,#20MORB
10858 Fitting
11159 Screw,Cap,Hex Hd,58″-11UNCx3-12″,Gr8,Pld,Dr Hd
11447
11526 Fitting
11555 Fitting, Hose, End, Crimp, Str, #12FJIC x #12Hose, Part # 11555, MFg. TESCO
11674 screw
11717 Fitting
12019 Fitting
12027 Fitting
12043 SLEEVE,ROTO,FTDA5187
12128 Fitting
12131 Fitting
12141 Fitting
12180 Fitting
12188 Fitting
12211 Fitting,Hyd,Str,#24MNPTx#16FNPT
12232
12253 Fitting,Hyd,90°Elb,#16FNPTx#16FNPT
12270 Fitting
12291 Fitting
12297 Fitting
12303 Fitting
12304 Fitting,Hyd,90°Elb,#8MJICx#6MORB
12525 Fitting,Hyd,Str,#16MORBx#16FJIC-Swvl
12788 Fitting,Hyd,90°Elb,#8MJICx#16MORB
12951 Counterbalance cylinder lug
12958 Radial bearing, Roller, spherical, CB, 260mm- Out. diameter x 170mm-Ø inside x 67mm-Width Bearing,Radial,Rlr,Sph,CB,260mm-ODx170mm-IDx67mm-W
12959 Bearing, Radial, Roller, Spherical, CB, 160mm Ø outer x 75mm Ø inner x 55mm wide Bearing,Radial,Rlr,Sph,CB,160mm-ODx75mm-IDx55mm-W
12960 Bearing, Radial, Roller, Spherical, CB, 140mm Ø outer x 65mm Ø inner x 48mm wide Bearing,Radial,Rlr,Sph,CB,140mm-ODx65mm-IDx48mm-W
12961 Radial bearing, Roller, spherical, CB, 110mm- Out. diameter x 50mm-Ø inside x 40mm-Width Bearing,Radial,Rlr,Sph,CB,110mm-ODx50mm-IDx40mm-W
12962 Ring seal, rubber, N70-376,9.725″ Ø inner x 0.210″ thickness O-Ring,N70-376,9.725″IDx0.210″Dia
12971 Oil level sight glass “OIL-RITE”, top drive gearbox (steel plug fitting with glass in cap), thread 2″NPT GLASS,SIGHT,2″NPT(OIL-RITE)
13097
13098 Sleeve,LoadNut,250-EMI-400450,HXI
13405 Mortgage key, steel, locking, reducer shaft, diam. 34″ x 18″ Width Key,Woodruff,34″Diax18″Wide
13414 PLUG,FARMINGTON
13516 Power supply
13518 MODULE,DIGITAL INPUT,VERSAMAX
13519 CARD,RELAY OUTPUT VERSAMAX
13520 CARD,ANALOG OUTPUT VERSAMAX
13544
13557 Bolt, Hex Head, 34″-10UNCx3″, Grade 8, Galvanized Head Lock Hole Screw,Cap,Hex Hd,34″-10UNCx3″,Gr8,Pld,Dr Hd
13560 nut
13561 nut
13574 Screw,Cap,Hex Hd,58″-11UNCx2-34″,Gr8,Pld,Dr Hd
13626 Cable,Bostrig,600V,110°C,#14,4C
13630 Cable gland, straight, steel, dia. 1.25″ (for cord 19.0 – 26.5mm) Gland,Cable,Ex,Str,1-14″,(Grommet 19.0mm-26.5mm)
13710 Barrier,Isolation,Digital,1In1Out,1Chan,23WireProx
13902
13923 MOUNT,NEEDLE VALVE,GRABBER HYD LOOP,EMI
14087
14089 Bracket, Upper Grabber Leg Coupling
14450 Bolt, Hex Head, 38″-16UNC x 2-14″, Grade 8, Electroplated, Head Lock Hole
14758 hose hyd
14759 Hose,Hyd,100R2-AT,#8×14″,FJICx90°FJIC
15056 Lock Nut, Electrical, 1-14″ Dia., Steel Nut,Lock,Elec,Ex,1-14″
15058 Ring seal, rubber, electrical, 1-14″ Ring,Sealing,Elec,Ex,1-14″
15520 Screw,Set,Skt Drive,Cup Pt,12″-13UNCx12″
15582
15608 Pin,Cotter
15662
15685 O-Ring, Metal Rubber, 1, 250″ Ø ID x 2.004″ OD x 0.250″ Width, CRW1 Seal,1.250″Shaftx2.004″ODx0.250″W,CRW1
15801
15965 Connector,Cable,90°Elb,34″,SR,(0.310″-0.560″)
16039 Pin,Cotter,18″ODx2-12″Lg,Pld
16186 Bearing, Radial, Roller, Tapered, 240mm Ø Outer x 160mm Ø Inner x 51mm Width Bearing,Radial,Rlr,Tpr,240mm-ODx160mm-IDx51mm-W
16188 Ring seal, rubber, N70-372,8.725″ Ø inner x 0.210″ thickness O-Ring,N70-372,8.725″IDx0.210″Dia
16210 nut
16213 Shield,Mud,Quill
16245 VALVE, RELIEF, 100-250 PSI, VENTATMOSPHERE
16262 Pump intermediate shaft adapter Mk3,EMI (steel sleeve with undercut) Adaptor,Pump,Intermediate Shaft,Mk3,EMI
16324
16361 Bolt, Hex Head, 14″-20UNC x 2″, Class 8, Electroplated, Head Lock Hole
16434 Pin,Cotter,116″ODx34″Lg,Pld
16499 Gripper hydraulic cylinder assembly, for HMI model GP (Manual 16499)
16552 Extention Port Clamp Box
16585 Washer,Flat,Type A,Narrow,516″,Hardened,Pld
16618 Screw
16706 Hose,Hyd,100R2-AT,#12×35″,FJICx90°FJIC
16720 hose hyd
16743 hose hyd
16764 Shackle, bolt lock, Shackle, Anvhor, Bolt-Type, G2130, 38”, 1Ton
720093 Kit,Intensifier,Grabber Box,EMI-400
720171 hose hyd
720195 Nut,Hex,Lock,Spiralock,Flg,12″-13SPL,Gr8,Pld
720196 Nut,Hex,Lock,Spiralock,Flg,78″-9SPL,Gr8,Pld
720197 Nut,Hex,Lock,Spiralock,Flg,1″-8SPL,Gr8,Pld
720222
720478 Fitting,Hyd,Str,#16MNPTx#8MNPT
720479
720644 seal
720690 Pump,Hyd,CCW,7.93cu-inrev&3.56cu-inrev Vane Pump
720691 Fitting
720821
720823 Screw,Cap,Hex Hd,14″-20UNCx3-12″,Gr8,Pld,Dr Hd
720892
721073 Kit,Major Repair,(For 3067A MSV)
721074 Repair kit, main, (for Mud gate valves 4185A and 5185B )
721308 Kit,Hub Conv. Upgrade,Actuator,5187-TDA-SER-A,5190-TDA-SER,
730081 Switch,2 Pos,RH Spring Rtn,LH Key Removal
730098
730103 Light,Pilot,Incan,120VAC,Grn,WBulb,Bayonet
730104 Light,Pilot,Incan,120VAC,Red,WBulb,Bayonet
730105 Light,Pilot,Incan,120VAC,Yel,WBulb,Bayonet
730111
730114 Light,Pilot,LED,120VAC,Yel,WBulb,Bayonet
730137 Light,Pilot,Incan,24VACDC,Grn,WBulb,Bayonet
730138
730139 Light,Pilot,Incan,24VACDC,Yel,WBulb,Bayonet
730553 Terminal bolt
730554
730780 Service Loop,225-ft lg,250-EMI-400
730806 Fitting
730807 seal
730809 screw
730812 Spring pin, locking, 532″ Ø external, 1″ length Pin,Spring,532″OD,1″Lg
730817 Kit,Hoses,Hyd,Service Loop,225-ft lg,EMI 400
730841
730843 Cord,Ext,Blower Motor,EMI 400,#14,7C,69M
730846 Cable Set,69m,Service Loop,EMI 400
730870 Cable gland, straight, steel, thread, 34″ (for cord 11.0 – 14.3 mm) Gland,Cable,Ex,Str,34″MNPT,(Grommet 11.0mm-14.3mm)
730873 Cord,Pigtail,Male,Robotics”A”,EMI 400,#14,37C,3M
730876 Cord Set,Pgtl,Male,Power,EMI 400,313 MCM,1C,3M
730879 seal
730958 Screw,Cap,Hex Hd,1″-8UNCx2-34″,Gr8,Pld,Dr Hd
730959 Screw,Cap,Hex Hd,58″-11UNCx1-34″,Gr8,Pld,Dr Hd
731006 731006 Bolt, hexagon head, 1″-8UNC x 4″, Grade 8, electroplated
731018 Screw,Cap,Hex Hd,1″-8UNCx7-12″,Gr8,Pld,Dr Hd
731028 Screw,Cap,Hex Hd,38″-16UNCx1-34″,Gr8,Pld,Dr Hd
731037 Fitting,Brass,45°Elb,#4Tubex#2MNPT(cw Insert)
731043 Screw
810334 Retainer,Pin,Yoke,Swivel,350-EXI-600
810340 Pin,Yoke,Link,350400-EXI-600
810344 Pin,Gearbox,Link,350400-EXI-600
810347 Retainer,Upper,Load Nut,350400-EXI-600
810377 Bushing,Load Collar,EXIESI
810389 Sleeve,Wear,Seal,Lower,Quill,350-EXI-600
810396
810419 Screw
810429 Bushing,Pipe,Cylinder Lock,EXIHXI
810596 hose hyd
820067 Shield,Mud,Gearbox,HXIT100
820111 Arm,Extend,Adjustable,EMI400HXI
820123 Shim, 0.020″ thick, Pipemanipulator Swivel, EMI 400 Shim,0.020″THK,Slew Drive,EMI 400
820124 Shim, 0.015″ thick, Pipemanipulator Swivel, EMI 400 Shim,0.015″THK,Slew Drive,EMI 400
820125 Shim, 0.025″ thick, Pipemanipulator Swivel, EMI 400 Shim,0.025″THK,Slew Drive,EMI 400
820136
820138 Bearing,Radial,Dbl-Rlr,Cyl,280mm-ODx200mm-IDx80mm-W
820141 Seal,Rotary,14-Port,EXIHXI
820143 Gear-Segment,Lock,Pipehandler,350-EXI-600
820146
820157 Shim,Retainer,Bearing,Upper,Quill,0.010″Thk
820158 Shim,Retainer,Bearing,Upper,Quill,0.005″Thk
820159 Shim,Retainer,Bearing,Upper,Quill,0.002″Thk
820161 Shim,Retainer,Bearing,Upper,Input,0.010″Thk
820163 Shim,Retainer,Bearing,Upper,Input,0.002″Thk
1120382 HPH Kit Kit, Aux Hydraulic, EMI 400, wGear Pump
1120442 Mount,Hyd Fittings,#4MNPT,Top Drive,EXIEMIHXI
1120443 hose hyd
1120450 hose hyd
1120454
1120458 Kit,Hoses,Aux Hyd,350-EXI-600
1120475 Motor, elec,, 575VAC50Hz, 15HP
1120477 Coupling,M48 Hub,42mm Dia Shaft,12mm Key,Bowex
1120478 Coupling,M48 Hub,1″ Dia Shaft,14″ Key,Bowex
1120479 Coupling,Sleeve,M48,Nylon,Bowex
1120480 Gear Pump, 3/4″, 20cc, 2400 rpm, 2500psi, keyed shaft, 1″ diameter, 2-bolt SAE B flange
1130006 hose hyd
1130087 hose hyd
1130090 hose hyd
1160172 hose hyd
1270173 Switch,Aux. Contacst,2,Form “C”
1270174 Coil,Trip,UV,Release,120V,FBreaker
1270223 Breaker,600V,800A,3P,50KAIC
1300001 seal

Send email to us

Product Detail

Product Tags

Previous: TDS TOP DRIVE SPARE PARTS: ASSY,IBOP,UPPER,PH-100,110103-500,REPAIR KIT,LWR IBOP H2S,99503-2,

Next: Tesco top deive spare parts

30123287

30123288

30123289

30123562

Write your message here and send it to us

Related products

JH Top Dive System (TDS) Spare Parts / Accessories

JH Top Dive Spare Parts List P/N. Name B17010001 Straight through pressure injection cup DQ50B-GZ-02 Blowout preventer DQ50B-GZ-04 Locking device assembly DQ50-D-04（YB021.123） pump M0101201.9 O-ring NT754010308 Flushing pipe assembly NT754010308-VI Spline shaft T75020114 Tilt cylinder flow control valve T75020201234 Hydraulic cylinder T75020401 Locking device assembly T75020402 Anti loosening fixing sleeve T75020403 Anti loosening chuck T75020503 Backup tong locating pin T75020504 Guide bol...

See more products >
Mechanical Drive Drilling Rig

The drawworks, rotary table and mud pumps of mechanical drive drilling rig are powered by diesel engine and driven by compound way, and the rig can be used for oil-gas field development on land below 7000m well depth. Mechanical Drive Drilling Rig Basic Parameters: Type ZJ20/1350L(J) ZJ30/1700L(J) ZJ40/2250L(J) ZJ50/3150L(J) ZJ70/4500L Nominal drilling depth 1200—2000 1600—3000 2500—4000 3500—5000 4500—7000 Max. hook load KN 1350 ...

See more products >
API 7K TYPE B MANUAL TONGS Drill String Handling

Type Q89-324/75(3 3/8-12 3/4 in)B Manual Tong is an essential tool in oil operation to fasten remove the screws of drill pipe and casing joint or coupling. It can be adjusted by changing latch lug jaws and handling shoulders. Technical Parameters No.of Latch Lug Jaws Latch Stop Size Pange Rated Torque in mm KN·m 5a 1 3 3/8-4 1/8 86-105 55 2 4 1/8-5 1/4 105-133 75 5b 1 4 1/4-5 1/4 108-133 75 2 5-5 3/4 127-146 75 3 6-6 3/4 152-171...

See more products >
Centrifuge for oil field Solids Control / Mud C...

Centrifuge is one of the important equipment of solid control. It is mainly used for removal of tiny harmful solid phase in drilling fluid. It can be also used for centrifugal sedimentation, drying, and unloading etc. Technical Features： • Compact structure, easy operation, strong working ability of single machine, and high separation quality. • Set vibration isolation structure to reduce complete machine’s vibration, with low noise and long time of trouble-free op...

See more products >
Vacuum Rake Type Heating Dryer new design

Simple type The half tube heats No base Add the short stanza tube Did not turn to move the part Specification: 1500L-3000L Common type Jacket heating With insulating layer Foot valve discharge port Specification: 1500L-10000L The whole type of figure Jacket heating Monoframe With gearing Specification: 1000L-10000L The half tube heats the type The half tube heats With water the rake teeth throughout, the double seals completely the structure Sprocket drive The whole ...

See more products >
Experiment Series Kneading Machine

Specifically for a variety of research structure, tertiary institutions and industrial and mining enterprises in lab and in test with can also be suitable for small batch precious materials experimental kneading. Species: common type, the vacuum type. Characteristics: the external appearance is elegant, the structure tightly packed, operate in brief, spread to move the stability. Choose the type please check the parameter watch of p9. Engineering: common type (Y), fl...

See more products >